For 0.90-1.00mm Insulated Conductor

Cable Range: O.D.≦6.5mm

---

The Pass-Through Cat 6A unshielded modular plugs accept from 24AWG to 26AWG stranded unshielded twisted pair cable with accommodation of insulated conductor from 0.90mm to 1.0mm. The Pass-Through plug gives you the convenience of threading the wires through the end wall and cutting them afterward. Only a very short untwisted length is presented while the cable is fully inserted into the taper, which is the secret to Cat 6A compliance. It works with 007A8401 Series Crimping Tool. Wire termination and cutting at the same time. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

For 0.70-0.80mm Insulated Conductor

w/SR for 4.5mm cable entrance

---

The “Small Conductor” Cat 6A unshielded modular plugs accept 26AWG and 28AWG slim cables. 28AWG UTP cable has a 0.69mm insulation diameter with nominal cable O.D. from 3.5mm to 4.8mm only. The 2-piece design has a “loading-bar” to accept from 0.70 to 0.80mm insulated conductors so all the thin wires can be placed on each slot. And the loading-bar is made in two rows - “6-up/2-down”, moving the green pair away from the other pairs. 3-prong blades further enhance the certainty of piercing the slim cable so excellent conductivity can be assured. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades

---

For 0.55-0.60mm Insulated Conductor

w/SR for 4.0mm cable entrance

---

The “Small Conductor” Cat 6A unshielded modular plugs accept 28AWG and 30AWG ultra-slim cables. 30AWG cable has nominal insulations at approximately 0.53mm only. The 2-piece design has a “loading-bar” to accept from 0.55 to 0.60mm insulated conductors so all the thin wires can be placed on each slot. And the loading-bar is made in two rows - “6-up/2-down”, moving the green pair away from the other pairs. Plug assembly that surpasses the Cat 6A specification is therefore feasible. 3-prong blades further enhance the certainty of piercing the ultra-slim cable so excellent conductivity can be assured. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades

---

Slim Boot (Embedded Type)

w/SR for 4.0mm/4.5mm cable entrance

---

The embedded boot provides the convenience when being used in fully populated blade switches or high density patch panels. The slender body is flush fit with the modular plug's width. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 4.0mm/5.0mm 5.5mm/6.0mm/6.5mm cable O.D. for options

---

For 1.00-1.10mm Insulated Conductor

“2pcs”, 6-up/2-down loading bar

---

The “Big Conductor” Cat 6A unshielded modular plugs accept from 23 to 26AWG, U/UTP solid or stranded twisted pair cable with accommodation of insulated conductor from 1.00mm to 1.10mm. The 2-piece design has a “loading-bar” to accept from 1.00 to 1.10mm insulated conductors so all the wires can be placed on each slot. And the loading-bar is made in two rows - “6-up/2-down”, moving the green pair away from the other pairs. Plug assembly that surpasses the Cat 6A specification is therefore feasible. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

For 0.90-1.00mm Insulated Conductor

“3pcs”, 1-row loading bar + windmill guide

---

Standard Cat 6A shielded modular plugs accept from 24AWG to 26AWG, stranded shielded twisted pair cable with accommodation of insulated conductor from 0.90mm to 1.0mm and cable O.D. less than 6.5mm. 3-piece design. Effective pair separation and maintaining the twist ratio are made possible by the "windmill guide". Together with the “loading bar” attached to it so each wire can be trimmed flush and steadily seated. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

Boot for Plug 88S50H90AD52

Suitable Cable Range: 4.5/5.2/6.0/6.5mm

---

Designed for ease of use in fully populated blade switches or high-density patch panels, the embedded boot features a slender body that seamlessly aligns with the width of the modular plug. This ensures there is no interference between neighboring ports. By fully inserting the two clips into the modular plug, the boot significantly enhances cable strain relief. Additionally, the boot is crafted from Polycarbonate (PC), a material known for its durability and resilience. The transparent housing eliminates the need for color matching cables, offering a universal fit with one boot for all. - PC UL94V-2 rated - 4.5/5.2/6.0/6.5mm O.D. for options

---

For 0.90-1.00mm Insulated Conductor

“2pcs”, 6-up/2-down loading bar

---

Standard Cat 6A shielded modular plugs accept from 24AWG to 26AWG, stranded shielded twisted pair cable with accommodation of insulated conductor from 0.90mm to 1.0mm and cable O.D. less than 6.5mm. 2-piece design. The “6-up/2-down loading bar” is made in two rows. It facilitates moving the green pair away from the other pairs. The most impedance-mismatched pair is put away so as to moderate the noises done to the other pairs. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

Boot for Plug 88S40370EC52

Suitable Cable Range: 4.0/4.5/5.0/5.5/6.0/6.5mm

---

The embedded boot provides the convenience when being used in fully populated blade switches or high density patch panels. The slender body is flush fit with the modular plug's width. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 4.0mm/5.0mm 5.5mm/6.0mm/6.5mm cable O.D. for options

---

For 0.90-1.00mm Insulated Conductor

“3pcs”, loading bar + windmill guide

---

Standard Cat 6A shielded modular plugs accept from 24AWG to 26AWG stranded shielded twisted pair cable with accommodation of insulated conductor from 0.90mm to 1.0mm. 3-piece design. The “windmill guide” helps to separate each pair and keep its twist ratio. The “loading bar” is made to attach to the guide so each wire can be trimmed flush and steadily seated. This may be the trick needed by many field installers to pass the "Cat 6A Patch Cord Test Limit." - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-0 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

Plug includes Boot w/Icon

Plug + φ6.7mm Boot + Boot Icon

---

Standard Cat 6A shielded modular plugs accept from 24AWG to 26AWG stranded shielded twisted pair cable with accommodation of insulated conductor from 0.90mm to 1.0mm. 3-piece design. The “windmill guide” helps to separate each pair and keep its twist ratio. The “loading bar” is made to attach to the guide so each wire can be trimmed flush and steadily seated. This may be the trick needed by many field installers to pass the "Cat 6A Patch Cord Test Limit." - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-0 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

Plug includes Boot w/Icon + Cable SR

Plug + φ6.7mm Boot + Boot Icon + Cable SR

---

Standard Cat 6A shielded modular plugs accept from 24AWG to 26AWG stranded shielded twisted pair cable with accommodation of insulated conductor from 0.90mm to 1.0mm. 3-piece design. The “windmill guide” helps to separate each pair and keep its twist ratio. The “loading bar” is made to attach to the guide so each wire can be trimmed flush and steadily seated. This may be the trick needed by many field installers to pass the "Cat 6A Patch Cord Test Limit." - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-0 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

Boot with Given Boot Icon + Cable SR

φ6.7mm Boot + Given Boot Icon + Cable SR

---

For 0.95-1.05mm Insulated Conductor

“2pcs”, 6-up/2-down loading bar

---

The Snagless Cat 6A shielded modular plugs accept from 24AWG to 26AWG stranded shielded twisted pair cable with accommodation of insulated conductor from 0.95mm to 1.05mm. 2-piece design. The loading bar is made in two rows - “6-up/2-down”. It facilitates moving the green pair away from the other pairs. The most impedance-mismatched pair is put away so as to moderate the noises done to the other pairs. Each wire is trimmed flush and steadily seated. Plug assembly that surpasses the Cat 6A specification is therefore feasible. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

For 1.30-1.40mm Insulated Conductor

Cable Range: O.D.≦7.5mm

---

The Pass-Through Cat 6A shielded modular plugs are made to accept 23AWG S/FTP foamed wires with accommodation of insulated conductor from 1.30mm to 1.40mm. The Pass-Through plug gives you the convenience of threading the wires through the loading bar. The “1357-up/2468-down loading bar” is made in two rows. It eases the tension throughout the assembling procedure instead of aligning in a single row. Simply insert the bar all the way till it reaches the narrow gate and cut all wires afterward. Only a very short untwisted length is presented with no room for kink and slack. The extremely short stripped length is the secret to Cat 6A compliance. The external grounding hook is built at the rear for encircling the screened braid of S/FTP cable. The 360-degree shield surrounding favors the screen effectiveness and shield integrity that high-speed Ethernet requires. It works with 007A8401 Series Crimping Tool. Wire termination and cutting at the same time. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application - Must work with 007A8401 Series Crimping Tool

---

For 0.55-0.60mm Insulated Conductor

w/SR for 4.0mm cable entrance

---

The “Small Conductor” Cat 6A shielded modular plugs accept 28AWG and 30AWG ultra-slim cables. 30AWG cable has nominal insulations at approximately 0.53mm only. The 2-piece design has a “loading-bar” to accept from 0.55 to 0.60mm insulated conductors so all the thin wires can be placed on each slot. And the loading-bar is made in two rows - “6-up/2-down”, moving the green pair away from the other pairs. Plug assembly that surpasses the Cat 6A specification is therefore feasible. 3-prong blades further enhance the certainty of piercing the ultra-slim cable so excellent conductivity can be assured. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades

---

For 1.35-1.45mm Insulated Conductor

“2pcs”, 4-up/4-down loading bar

---

The “Big Conductor w/Hook” Cat 6A shielded modular plugs are made to accept 23AWG S/FTP foamed wires with accommodation of insulated conductor from 1.35mm to 1.45mm and cable O.D. less than 8.0mm. This could be the plug that accommodates the largest foamed wires on the market so far! 2-piece design. The “4-up/4-down loading bar” is made in two rows. It eases the tension throughout the assembling procedure instead of aligning in a single row. It artfully enlarges the spacing between “pin 3 to pin 4” and “pin 5 to pin 6”. In this way, the noise between the blue and green pair can be mitigated so as to easily pass “Cat 6A Patch Cord Test Limit”. The external grounding hook is built at the rear for encircling the screened braid of S/FTP cable. The 360-degree shield surrounding favors the screen effectiveness and shield integrity that high-speed Ethernet requires. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

Slim Boot (Embedded Type)

Suitable Cable Range: 5.0/5.5/6.0/6.5mm

---

The embedded boot provides the convenience when being used in fully populated blade switches or high density patch panels. The slender body is flush fit with the modular plug's width. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 5.0mm/5.5mm/6.0mm/6.5mm cable O.D. for options

---

Slim Boot (Embedded Type)

Suitable Cable Range: 4.0/4.5/5.0/5.5/6.5mm

---

The embedded boot provides the convenience when being used in fully populated blade switches or high density patch panels. The slender body is flush fit with the modular plug's width. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 4.0mm/5.0mm 5.5mm/6.0mm/6.5mm cable O.D. for options

---

Snagless Boot (Embedded Type)

Regular Length, 6.0φ and 6.5φ for Options

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. A single boot fits all.

---

Snagless Boot (Embedded Type)

Short Body, 4.7φ and 6.5φ for Options

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. Comparing to regular snagless boot P/N. SR511E02, this short snagless boot further enables cable-bending in a relatively narrower space. The transparent housing saves you from matching the colors of cables. One single boot fits all.

---

Outer Coated Type

Φ5.5 to 6.5mm

---

The outer coated boots are made for reducing the cable strain when using solid cables with a diameter of approximately 6.0+-0.5mm. The boot is made of PVC, which elastically guards the cable and plug connection. The interdigit cone tail protects against improper bending that might result in signal reflections and intermittence of networks.

---

For Snagless Plug

Regular

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. A single boot fits all.

---

For Snagless Plug

Short

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. Comparing to regular snagless boot P/N. SR511E02, this short snagless boot further enables cable-bending in a relatively narrower space. The transparent housing saves you from matching the colors of cables. One single boot fits all.

---