For 1.30-1.40mm Insulated Conductor

Cable Range: O.D.≦7.5mm

---

The Pass-Through Cat 6A shielded modular plugs are made to accept 23AWG S/FTP foamed wires with accommodation of insulated conductor from 1.30mm to 1.40mm. The Pass-Through plug gives you the convenience of threading the wires through the loading bar. The “1357-up/2468-down loading bar” is made in two rows. It eases the tension throughout the assembling procedure instead of aligning in a single row. Simply insert the bar all the way till it reaches the narrow gate and cut all wires afterward. Only a very short untwisted length is presented with no room for kink and slack. The extremely short stripped length is the secret to Cat 6A compliance. The external grounding hook is built at the rear for encircling the screened braid of S/FTP cable. The 360-degree shield surrounding favors the screen effectiveness and shield integrity that high-speed Ethernet requires. It works with 007A8401 Series Crimping Tool. Wire termination and cutting at the same time. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application - Must work with 007A8401 Series Crimping Tool

---

For 0.55-0.60mm Insulated Conductor

w/SR for 4.0mm cable entrance

---

The “Small Conductor” Cat 6A shielded modular plugs accept 28AWG and 30AWG ultra-slim cables. 30AWG cable has nominal insulations at approximately 0.53mm only. The 2-piece design has a “loading-bar” to accept from 0.55 to 0.60mm insulated conductors so all the thin wires can be placed on each slot. And the loading-bar is made in two rows - “6-up/2-down”, moving the green pair away from the other pairs. Plug assembly that surpasses the Cat 6A specification is therefore feasible. 3-prong blades further enhance the certainty of piercing the ultra-slim cable so excellent conductivity can be assured. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades

---

For 1.35-1.45mm Insulated Conductor

“2pcs”, 4-up/4-down loading bar

---

The “Big Conductor w/Hook” Cat 6A shielded modular plugs are made to accept 23AWG S/FTP foamed wires with accommodation of insulated conductor from 1.35mm to 1.45mm and cable O.D. less than 8.0mm. This could be the plug that accommodates the largest foamed wires on the market so far! 2-piece design. The “4-up/4-down loading bar” is made in two rows. It eases the tension throughout the assembling procedure instead of aligning in a single row. It artfully enlarges the spacing between “pin 3 to pin 4” and “pin 5 to pin 6”. In this way, the noise between the blue and green pair can be mitigated so as to easily pass “Cat 6A Patch Cord Test Limit”. The external grounding hook is built at the rear for encircling the screened braid of S/FTP cable. The 360-degree shield surrounding favors the screen effectiveness and shield integrity that high-speed Ethernet requires. - UL Listed, TIA-1096 and IEC 60603-7 compliant - PC UL94V-2 rated plug housing, 50u” gold plated contact blades - Supports PoE type 4 (PoE++) application

---

Slim Boot (Embedded Type)

Suitable Cable Range: 5.0/5.5/6.0/6.5mm

---

The embedded boot provides the convenience when being used in fully populated blade switches or high density patch panels. The slender body is flush fit with the modular plug's width. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 5.0mm/5.5mm/6.0mm/6.5mm cable O.D. for options

---

Slim Boot (Embedded Type)

Suitable Cable Range: 4.0/4.5/5.0/5.5/6.5mm

---

The embedded boot provides the convenience when being used in fully populated blade switches or high density patch panels. The slender body is flush fit with the modular plug's width. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 4.0mm/5.0mm 5.5mm/6.0mm/6.5mm cable O.D. for options

---

Snagless Boot (Embedded Type)

Regular Length, 6.0φ and 6.5φ for Options

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. A single boot fits all.

---

Snagless Boot (Embedded Type)

Short Body, 4.7φ and 6.5φ for Options

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. Comparing to regular snagless boot P/N. SR511E02, this short snagless boot further enables cable-bending in a relatively narrower space. The transparent housing saves you from matching the colors of cables. One single boot fits all.

---

Outer Coated Type

Φ5.5 to 6.5mm

---

The outer coated boots are made for reducing the cable strain when using solid cables with a diameter of approximately 6.0+-0.5mm. The boot is made of PVC, which elastically guards the cable and plug connection. The interdigit cone tail protects against improper bending that might result in signal reflections and intermittence of networks.

---

For Snagless Plug

Regular

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. A single boot fits all.

---

For Snagless Plug

Short

---

When employed in fully populated blade switches or high-density patch panels, the embedded boot offers ease. The slender body is flush fit with the modular plug's width. There won't be any port conflicts as a result. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. Comparing to regular snagless boot P/N. SR511E02, this short snagless boot further enables cable-bending in a relatively narrower space. The transparent housing saves you from matching the colors of cables. One single boot fits all.

---

For C5e Plug

Φ5.5mm to 6.5mm

---

The embedded boot provides convenience when being used in fully populated blade switches or high density patch panels. The slender body is flush fit with the modular plug's width. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 5.5mm/6.0mm/6.5mm cable O.D. for options

---

For C6/C6A Plug

Φ4.0mm to 6.5mm

---

The embedded boot provides convenience when being used in fully populated blade switches or high density patch panels. The slender body sits flush with the RJ-45 plug. There will be no interference between neighboring ports. The two clips can be fully inserted into the modular plug which enhances the relief of cable strain. Additionally, the boot is made of Polycarbonate (PC), which is both durable and resilient. The transparent housing saves you from matching the colors of cables. One boot fits all. - PC UL94V-2 rated - 4.0mm/5.0mm 5.5mm/6.0mm/6.5mm cable O.D. for options

---

Crimping Tool for Snagless Thru Plugs

Works with HCI Snagless Pass-Through Series

---

Crimp and cut HCI Snagless Pass-Through Plug Series (UTP plug: 88U51220AD52, 88U5122S1D52; STP plug: 88S51440AD52, 88S51430AD52) with this custom-made 007A8502 Plug Crimping Tool. Comes with dual cavity ground crimp to wrap STP plug's ground collar onto cable. The horizontal crimping design gives a relatively flat and consistent force to minimize uneven pressure or distortion for consistent and high-quality termination with its stable and straightforward crimping motion.

---

For 23AWG S/FTP

Φ7.0mm to 8.0mm

---

The outer coated boots are made for relieving the cable strain when using large O.D. cable such as Cat 6A S/FTP 23AWG with a diameter of approximately 7.5+-0.5mm. The boot is constructed of PVC which gives a lot of friction between cable and plug. The flexible cone tail guards against improper bending radius that might cause downtime of networks.

---

Large O.D. Boot (Coated Type)

Suitable Cable Range: 7.0/7.5/8.0mm

---

The outer coated boots are made for relieving the cable strain when using large O.D. cable such as Cat 6A S/FTP 23AWG with a diameter of approximately 7.5+-0.5mm. The boot is constructed of PVC which gives a lot of friction between cable and plug. The flexible cone tail guards against improper bending radius that might cause downtime of networks. - 7.0mm/7.5mm/8.0mm cable O.D. for options

---

For C5e STP plug

Φ6.4mm

---

The integrated boot offers convenience when using it in densely populated blade switches or high-density patch panels. Its slim body seamlessly aligns with the width of the modular plug, ensuring no interference between adjacent ports. The distinguishing feature of this boot is its composition(double-shot), as it is crafted using a dual-material design. The two claws responsible for securely gripping the modular plug are constructed from rigid PC (Polycarbonate) material. Meanwhile, the tail boot is fabricated from a flexible PVC material, enabling free-directional orientation without any constraints. - PC(claws)/PVC(tail boot) UL94V-2 rated - For approximately 6.4mm shielded cable O.D.

---

For C6/ C6A UTP plug

Φ6.4mm

---

The integrated boot offers convenience when using it in densely populated blade switches or high-density patch panels. Its slim body seamlessly aligns with the width of the modular plug, ensuring no interference between adjacent ports. The distinguishing feature of this boot is its composition(double-shot), as it is crafted using a dual-material design. The two claws responsible for securely gripping the modular plug are constructed from rigid PC (Polycarbonate) material. Meanwhile, the tail boot is fabricated from a flexible PVC material, enabling free-directional orientation without any constraints. - PC(claws)/PVC(tail boot) UL94V-2 rated - For approximately 6.4mm unshielded cable O.D.

---

For C6/ C6A STP plug

Φ6.5mm

---

The integrated boot offers convenience when using it in densely populated blade switches or high-density patch panels. Its slim body seamlessly aligns with the width of the modular plug, ensuring no interference between adjacent ports. The distinguishing feature of this boot is its composition(double-shot), as it is crafted using a dual-material design. The two claws responsible for securely gripping the modular plug are constructed from rigid PC (Polycarbonate) material. Meanwhile, the tail boot is fabricated from a flexible PVC material, enabling free-directional orientation without any constraints. - PC(claws)/PVC(tail boot) UL94V-2 rated - For approximately 6.5mm shielded cable O.D.

---

Cable Tester

---

Cable Stripper

---